Beam CalculatorLoads, sections & elastic response

Beam calculators / Supports & loading

Trace the load. Understand the beam.

Beam Calculator

Calculate reactions, shear, bending moment and elastic deflection. Start below or explore 80 focused tools with computed tables and published method references.

Your beam, explained visually

Pin A · Roller B

Your beam & loading inputs

m
GPa
cm⁴
mm
kN/m
kN/m
kN
ratio

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

Choose your calculation

All beam calculators

Beam supports, loading cases, section geometry and bounded elastic models.

Supports & loading

Beam CalculatorSimply Supported Beam Uniform Load CalculatorSimply Supported Beam Point Load CalculatorSimply Supported Beam Triangular Load CalculatorCantilever Beam Uniform Load CalculatorCantilever Beam Point Load CalculatorCantilever Beam Triangular Load CalculatorFixed Both Ends Beam Uniform Load CalculatorFixed Both Ends Beam Point Load CalculatorFixed Both Ends Beam Triangular Load CalculatorPropped Cantilever Beam Uniform Load CalculatorPropped Cantilever Beam Point Load CalculatorPropped Cantilever Beam Triangular Load CalculatorTwo Span Continuous Beam Uniform Load CalculatorTwo Span Continuous Beam Point Load CalculatorTwo Span Continuous Beam Triangular Load CalculatorOverhanging Beam Uniform Load CalculatorOverhanging Beam Point Load CalculatorOverhanging Beam Triangular Load CalculatorBeam Bending Moment CalculatorBeam Shear Force CalculatorBeam Support Reaction CalculatorBeam Slope and Rotation CalculatorSimply Supported Beam Influence Line Calculator

Cross-section geometry

Rectangular Section Properties CalculatorCircular Section Properties CalculatorBox Section Properties CalculatorHollow Circular Section Properties CalculatorI Beam Section Properties CalculatorChannel Section Properties CalculatorT Beam Section Properties CalculatorAngle Section Properties Calculator

Material & section models

Steel Beam Deflection CalculatorSteel Beam Point Load CalculatorAluminum Beam Deflection CalculatorAluminum Beam Point Load CalculatorWood Beam Deflection CalculatorWood Beam Point Load CalculatorLVL Beam Deflection CalculatorLVL Beam Point Load CalculatorGlulam Beam Deflection CalculatorGlulam Beam Point Load CalculatorConcrete Beam Deflection CalculatorConcrete Beam Point Load CalculatorSquare Tube Beam Deflection CalculatorSquare Tube Beam Point Load Calculator

Model-only limits

Rectangular Beam Model Load Bound CalculatorRectangular Beam Elastic Span Bound CalculatorI Beam Model Load Bound CalculatorI Beam Elastic Span Bound CalculatorBox Beam Model Load Bound CalculatorBox Beam Elastic Span Bound CalculatorRequired Beam Moment of Inertia CalculatorRectangular Beam Depth Bound Calculator

Stress & stiffness

Rectangular Beam Bending and Shear Stress CalculatorI Beam Bending and Shear Stress CalculatorBox Beam Bending and Shear Stress CalculatorCircular Beam Bending and Shear Stress CalculatorBeam Flexural Stiffness CalculatorFlitch Beam Elastic Stiffness Calculator

Dynamics & axial buckling

Simply Supported Beam Natural Frequency CalculatorCantilever Beam Natural Frequency CalculatorFixed Both Ends Beam Natural Frequency CalculatorBeam Euler Axial Buckling Calculator

Weight, surface & cost

Rectangular Beam Weight CalculatorI Beam Weight CalculatorBox Beam Weight CalculatorT Beam Weight CalculatorI Beam Surface Area CalculatorBeam Cost Calculator

Loads & geometry

Tributary Beam Load CalculatorFloor Beam Load CalculatorRoof Beam Load CalculatorWall Load on Beam CalculatorRidge Beam Height Geometry Calculator

Optical & lighting beams

Gaussian Beam Propagation CalculatorGaussian Beam Divergence CalculatorGaussian Beam Waist from Divergence CalculatorGaussian Beam Peak Intensity CalculatorLighting Beam Angle Footprint Calculator

The method

Formula and calculation steps

EId4vdx4=q(x)
dMdx=V
dVdx=q(x)

Hermite beam stiffness uses consistent distributed loads. Exact element load integration recovers the response; q(x) is positive upward.

Calculate support reactions, shear force, bending moment, slope and elastic deflection for the stated simply supported beam.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Straight prismatic Euler–Bernoulli beam; linear elastic material, constant EI, small displacement and ideal supports. No shear deformation, lateral-torsional buckling, connection design, material failure, code factors or certified safe load.

Beam: model and interpretation

Calculate support reactions, shear force, bending moment, slope and elastic deflection for the stated simply supported beam. Straight prismatic Euler–Bernoulli beam; linear elastic material, constant EI, small displacement and ideal supports. No shear deformation, lateral-torsional buckling, connection design, material failure, code factors or certified safe load.
The x coordinate runs from left to right. Deflection and vertical reaction are positive upward; rotation and external reaction moment are positive counterclockwise; sagging internal moment is positive. Downward load inputs are converted to negative distributed q in the equilibrium equations. The member has constant EI across its modeled length.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Beam Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Beam length / first span = 6 m; Entered elastic modulus = 200 GPa; Second moment of area Ix = 8000 cm⁴; Extreme-fibre distance = 150 mm; Downward line load at left end = 3 kN/m; Downward line load at right end = 7 kN/m; Downward point load = 10 kN; Load position / total length = 0.4 ratio.

OutputComputed result
Maximum absolute elastic deflection7.929553 mm
Signed extreme deflection-7.929553 mm upward
Deflection extreme location2.96787 m from left
Maximum absolute deflection0.312187 in
Signed extreme moment35.424 kN·m sagging
Signed extreme shear-21 kN
Signed extreme rotation-0.004177 rad
Extreme-fibre bending magnitude66.42 MPa
Section Ix8,000 cm⁴
Support at x=0 m vertical19 kN upward
Support at x=6 m vertical21 kN upward

How the stated input changes the result

ScenarioChanged input / basisResult
3 mBeam length / first span0.661912 mm
4.5 mBeam length / first span2.789485 mm
6 mBeam length / first span7.929553 mm
7.5 mBeam length / first span18.061242 mm
9 mBeam length / first span35.658191 mm
12 mBeam length / first span105.615016 mm

Unchanged inputs use: Dimension units = Metric dimensions; Beam length / first span = 6 m; Entered elastic modulus = 200 GPa; Second moment of area Ix = 8000 cm⁴; Extreme-fibre distance = 150 mm; Downward line load at left end = 3 kN/m; Downward line load at right end = 7 kN/m; Downward point load = 10 kN; Load position / total length = 0.4 ratio. Results retain the model limitations described above.

Common questions

Are the plotted lines also used to locate the maximum?

The plotted points illustrate the response. Extrema are evaluated separately at element boundaries and roots of the exact equilibrium/rotation polynomials, including the distributed-load displacement term.

Does this include shear deformation or lateral-torsional buckling?

No. This is a small-deflection Euler–Bernoulli bending model. Thick/short beams, stability, support bearing, connections, material failure and full design-code checks require additional analysis.

What limitation matters for this calculation?

Straight prismatic Euler–Bernoulli beam; linear elastic material, constant EI, small displacement and ideal supports. No shear deformation, lateral-torsional buckling, connection design, material failure, code factors or certified safe load.

How do I use this beam calculator?

Calculate support reactions, shear force, bending moment, slope and elastic deflection for the stated simply supported beam.
EId4vdx4=q(x)
dMdx=V
dVdx=q(x)

Hermite beam stiffness uses consistent distributed loads. Exact element load integration recovers the response; q(x) is positive upward.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • American Wood Council Design Aid 6: Beam Design Formulas, simple uniform and central point-load caseshttps://awc.org/wp-content/uploads/2021/12/AWC-DA6-BeamFormulas-0710.pdf
  • Delft University of Technology, L. Bosscher thesis, Appendix A.1 equations A.1–A.9: Euler–Bernoulli beam stiffnesshttps://repository.tudelft.nl/file/File_5cfe79e8-3268-45fd-a0a2-ec9130ea63b7
  • Penn State Mechanics Map: area moments of inertia by composite parts and parallel-axis theoremhttps://mechanicsmap.psu.edu/websites/A2_moment_intergrals/A2-9_area_moments_composite/areamomentcomposite.html
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors