Beam CalculatorLoads, sections & elastic response

Beam calculators / Model-only limits

Trace the load. Understand the beam.

Rectangular Beam Depth Bound Calculator

Calculate a continuous rectangular depth from supplied bending and deflection reference limits.

Your model, explained visually

Model geometry

Your beam & loading inputs

mm
m
GPa
kN/m
MPa

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

hB=6wL28bσref
hδ=5wL3n32Eb3
hrequired=max(hB,hδ)

Choose the larger depth from the bending-reference and deflection-reference expressions.

Calculate a continuous rectangular depth from supplied bending and deflection reference limits.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Model-only simply supported UDL inverse, not a timber grade or safe member selection; no shear, bearing, connections or stability.

Rectangular Beam Depth Bound: model and interpretation

Calculate a continuous rectangular depth from supplied bending and deflection reference limits. Model-only simply supported UDL inverse, not a timber grade or safe member selection; no shear, bearing, connections or stability.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Rectangular Beam Depth Bound Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Fixed rectangular width = 150 mm; Beam length / first span = 6 m; Elastic modulus = 10 GPa; Uniform line load = 3 kN/m; Supplied reference bending stress = 10 MPa; Chosen deflection denominator L/n = 360 .

OutputComputed result
Largest model-only rectangular depth bound289.646815 mm
Bending-reference depth232.379001 mm
Deflection-reference depth289.646815 mm

How the stated input changes the result

ScenarioChanged input / basisResult
3 mBeam length / first span144.823408 mm
4.5 mBeam length / first span217.235112 mm
6 mBeam length / first span289.646815 mm
7.5 mBeam length / first span362.058519 mm
9 mBeam length / first span434.470223 mm
12 mBeam length / first span579.293631 mm

Unchanged inputs use: Dimension units = Metric dimensions; Fixed rectangular width = 150 mm; Beam length / first span = 6 m; Elastic modulus = 10 GPa; Uniform line load = 3 kN/m; Supplied reference bending stress = 10 MPa; Chosen deflection denominator L/n = 360 . Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Model-only simply supported UDL inverse, not a timber grade or safe member selection; no shear, bearing, connections or stability.

How do I use this rectangular beam depth bound calculator?

Calculate a continuous rectangular depth from supplied bending and deflection reference limits.
hB=6wL28bσref
hδ=5wL3n32Eb3
hrequired=max(hB,hδ)

Choose the larger depth from the bending-reference and deflection-reference expressions.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • American Wood Council Design Aid 6: Beam Design Formulas, simple uniform and central point-load caseshttps://awc.org/wp-content/uploads/2021/12/AWC-DA6-BeamFormulas-0710.pdf
  • Penn State Mechanics Map: area moments of inertia by composite parts and parallel-axis theoremhttps://mechanicsmap.psu.edu/websites/A2_moment_intergrals/A2-9_area_moments_composite/areamomentcomposite.html
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors