Beam CalculatorLoads, sections & elastic response

Beam calculators / Cross-section geometry

Trace the load. Understand the beam.

Hollow Circular Section Properties Calculator

Calculate area, centroid, second moments of area and elastic section moduli for an ideal hollow circular cross section.

Your section, explained visually

Section geometry

Your beam & loading inputs

mm
mm

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

A=∑iAi
y¯=∑iAiyiA
Ix=∑i(Ix,i+AiΔyi2)
S=Ic

Composite parts use their own centroidal second moments and distances to the overall centroid. S is the elastic section modulus.

Calculate area, centroid, second moments of area and elastic section moduli for an ideal hollow circular cross section.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Actual dimensions, square corners and no fillets. Angle sections also have a nonzero product of inertia; their centroidal axes are not generally principal bending axes. No torsional constant or shear-centre analysis.

Hollow Circular Section Properties: model and interpretation

Calculate area, centroid, second moments of area and elastic section moduli for an ideal hollow circular cross section. Actual dimensions, square corners and no fillets. Angle sections also have a nonzero product of inertia; their centroidal axes are not generally principal bending axes. No torsional constant or shear-centre analysis.
Non-overlapping rectangular parts are assembled by area integration and the parallel-axis theorem; circular and annular sections use their exact ideal geometry. Rolled fillets, corner radii, local effective-width reductions and catalogue tolerances are excluded. Centroidal horizontal and vertical axes are not necessarily principal axes for an angle.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Hollow Circular Section Properties Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Outside / solid diameter = 100 mm; Wall thickness = 5 mm.

OutputComputed result
Centroidal horizontal-axis second moment168.811518 cm⁴
Area1,492.25651 mm²
Centroid x from left50 mm
Centroid y from bottom50 mm
Centroidal Iy168.811518 cm⁴
Centroidal product Ixy0 cm⁴
Principal Imax168.811518 cm⁴
Principal Imin168.811518 cm⁴
Elastic Sx top33.762304 cm³
Elastic Sx bottom33.762304 cm³

How the stated input changes the result

ScenarioChanged input / basisResult
50 mmOutside / solid diameter18.113245 cm⁴
75 mmOutside / solid diameter67.691504 cm⁴
100 mmOutside / solid diameter168.811518 cm⁴
125 mmOutside / solid diameter339.881055 cm⁴
150 mmOutside / solid diameter599.307886 cm⁴
200 mmOutside / solid diameter1,456.864506 cm⁴

Unchanged inputs use: Dimension units = Metric dimensions; Outside / solid diameter = 100 mm; Wall thickness = 5 mm. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Actual dimensions, square corners and no fillets. Angle sections also have a nonzero product of inertia; their centroidal axes are not generally principal bending axes. No torsional constant or shear-centre analysis.

How do I use this hollow circular section properties calculator?

Calculate area, centroid, second moments of area and elastic section moduli for an ideal hollow circular cross section.
A=∑iAi
y¯=∑iAiyiA
Ix=∑i(Ix,i+AiΔyi2)
S=Ic

Composite parts use their own centroidal second moments and distances to the overall centroid. S is the elastic section modulus.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Penn State Mechanics Map: area moments of inertia by composite parts and parallel-axis theoremhttps://mechanicsmap.psu.edu/websites/A2_moment_intergrals/A2-9_area_moments_composite/areamomentcomposite.html
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors