Beam CalculatorLoads, sections & elastic response

Beam calculators / Weight, surface & cost

Trace the load. Understand the beam.

T Beam Weight Calculator

Calculate theoretical t beam mass, kg/m, lb/ft and gravitational line load from actual dimensions.

Your section, explained visually

Section geometry

Your beam & loading inputs

mm
mm
mm
mm
m
kg/m³

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

m=ρAL
wself=ρAg

m is theoretical mass; A is section area; ρ is mass density; g is gravitational acceleration.

Calculate theoretical t beam mass, kg/m, lb/ft and gravitational line load from actual dimensions.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Geometric mass only, no rounded stock-table weights, fillets, coatings, welds or tolerances. Density is an editable example.

T Beam Weight: model and interpretation

Calculate theoretical t beam mass, kg/m, lb/ft and gravitational line load from actual dimensions. Geometric mass only, no rounded stock-table weights, fillets, coatings, welds or tolerances. Density is an editable example.
Geometric quantity and elastic capacity are different calculations. Actual dimensions and supplied density determine theoretical mass. Painting area follows exposed perimeter and length, while cost evaluates only the rate and additional charge entered by the user.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

T Beam Weight Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Overall flange / section width = 150 mm; Overall section depth = 300 mm; Web thickness = 8 mm; Flange thickness = 12 mm; Beam length / first span = 6 m; Supplied material density = 7850 kg/m³.

OutputComputed result
Theoretical dimensioned beam mass193.2984 kg
Mass426.150025 lb
Mass per length32.2164 kg/m
Mass per length21.648421 lb/ft
Gravity self-weight line load0.315935 kN/m
Material volume0.024624 m³

How the stated input changes the result

ScenarioChanged input / basisResult
3 mBeam length / first span96.6492 kg
4.5 mBeam length / first span144.9738 kg
6 mBeam length / first span193.2984 kg
7.5 mBeam length / first span241.623 kg
9 mBeam length / first span289.9476 kg
12 mBeam length / first span386.5968 kg

Unchanged inputs use: Dimension units = Metric dimensions; Overall flange / section width = 150 mm; Overall section depth = 300 mm; Web thickness = 8 mm; Flange thickness = 12 mm; Beam length / first span = 6 m; Supplied material density = 7850 kg/m³. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Geometric mass only, no rounded stock-table weights, fillets, coatings, welds or tolerances. Density is an editable example.

How do I use this t beam beam weight calculator?

Calculate theoretical t beam mass, kg/m, lb/ft and gravitational line load from actual dimensions.
m=ρAL
wself=ρAg

m is theoretical mass; A is section area; ρ is mass density; g is gravitational acceleration.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Penn State Mechanics Map: area moments of inertia by composite parts and parallel-axis theoremhttps://mechanicsmap.psu.edu/websites/A2_moment_intergrals/A2-9_area_moments_composite/areamomentcomposite.html
  • OpenStax University Physics, density is mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors