Beam CalculatorLoads, sections & elastic response

Beam calculators / Model-only limits

Trace the load. Understand the beam.

Rectangular Beam Model Load Bound Calculator

Find the smaller bending-reference and deflection-reference uniform load bound under the printed elastic model.

Your model, explained visually

Model geometry

Your beam & loading inputs

mm
mm
GPa
MPa
m

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Mmax=wL28
δmax=5wL4384EI
δref=Ln

Simply supported beam under a uniform load. Compare bending stress with the supplied reference and deflection with L/n.

Find the smaller bending-reference and deflection-reference uniform load bound under the printed elastic model.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Not a safe capacity, stock-section selection or code design. Reference stress and L/n are supplied, not prescribed; shear, stability, connections, support bearing and load factors are excluded.

Rectangular Beam Model Load Bound: model and interpretation

Find the smaller bending-reference and deflection-reference uniform load bound under the printed elastic model. Not a safe capacity, stock-section selection or code design. Reference stress and L/n are supplied, not prescribed; shear, stability, connections, support bearing and load factors are excluded.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Rectangular Beam Model Load Bound Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Overall flange / section width = 150 mm; Overall section depth = 300 mm; Entered elastic modulus = 200 GPa; Supplied reference bending stress = 150 MPa; Chosen deflection denominator L/n = 360 ; Beam length / first span = 6 m.

OutputComputed result
Smallest model-only uniform-load bound66.666667 kN/m
Bending-reference bound75 kN/m
Deflection-reference bound66.666667 kN/m

How the stated input changes the result

ScenarioChanged input / basisResult
3 mBeam length / first span300 kN/m
4.5 mBeam length / first span133.333333 kN/m
6 mBeam length / first span66.666667 kN/m
7.5 mBeam length / first span34.133333 kN/m
9 mBeam length / first span19.753086 kN/m
12 mBeam length / first span8.333333 kN/m

Unchanged inputs use: Dimension units = Metric dimensions; Overall flange / section width = 150 mm; Overall section depth = 300 mm; Entered elastic modulus = 200 GPa; Supplied reference bending stress = 150 MPa; Chosen deflection denominator L/n = 360 ; Beam length / first span = 6 m. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Not a safe capacity, stock-section selection or code design. Reference stress and L/n are supplied, not prescribed; shear, stability, connections, support bearing and load factors are excluded.

How do I use this rectangular beam model load bound calculator?

Find the smaller bending-reference and deflection-reference uniform load bound under the printed elastic model.
Mmax=wL28
δmax=5wL4384EI
δref=Ln

Simply supported beam under a uniform load. Compare bending stress with the supplied reference and deflection with L/n.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • American Wood Council Design Aid 6: Beam Design Formulas, simple uniform and central point-load caseshttps://awc.org/wp-content/uploads/2021/12/AWC-DA6-BeamFormulas-0710.pdf
  • Penn State Mechanics Map: area moments of inertia by composite parts and parallel-axis theoremhttps://mechanicsmap.psu.edu/websites/A2_moment_intergrals/A2-9_area_moments_composite/areamomentcomposite.html
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors