Beam CalculatorLoads, sections & elastic response

Beam calculators / Dynamics & axial buckling

Trace the load. Understand the beam.

Cantilever Beam Natural Frequency Calculator

Calculate first ideal transverse bending frequency for a cantilever uniform beam.

Your model, explained visually

Model geometry

Your beam & loading inputs

m
GPa
cm⁴
kg/m

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

f1=β122πL2EIμ

μ is mass per unit length. β₁ is the boundary-condition root used by this page; stiffness and mass must use consistent units.

Calculate first ideal transverse bending frequency for a cantilever uniform beam.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Uniform EI and distributed mass, no axial force, attached point masses, damping or shear/rotary-inertia effects. Not a resonance safety assessment.

Cantilever Beam Natural Frequency: model and interpretation

Calculate first ideal transverse bending frequency for a cantilever uniform beam. Uniform EI and distributed mass, no axial force, attached point masses, damping or shear/rotary-inertia effects. Not a resonance safety assessment.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Cantilever Beam Natural Frequency Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Beam length / first span = 6 m; Elastic modulus = 200 GPa; Second moment of area = 8000 cm⁴; Uniform mass per length = 30 kg/m.

OutputComputed result
First ideal transverse bending frequency11.351879 Hz

How the stated input changes the result

ScenarioChanged input / basisResult
3 mBeam length / first span45.407515 Hz
4.5 mBeam length / first span20.181118 Hz
6 mBeam length / first span11.351879 Hz
7.5 mBeam length / first span7.265202 Hz
9 mBeam length / first span5.045279 Hz
12 mBeam length / first span2.83797 Hz

Unchanged inputs use: Dimension units = Metric dimensions; Beam length / first span = 6 m; Elastic modulus = 200 GPa; Second moment of area = 8000 cm⁴; Uniform mass per length = 30 kg/m. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Uniform EI and distributed mass, no axial force, attached point masses, damping or shear/rotary-inertia effects. Not a resonance safety assessment.

How do I use this cantilever beam natural frequency calculator?

Calculate first ideal transverse bending frequency for a cantilever uniform beam.
f1=β122πL2EIμ

μ is mass per unit length. β₁ is the boundary-condition root used by this page; stiffness and mass must use consistent units.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • University of Nebraska–Lincoln, S. Whitney: Vibrations of Cantilever Beamshttps://emweb.unl.edu/mechanics-pages/scott-whitney/325hweb/beams.htm
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors
  • University of Nebraska–Lincoln, S. Whitney: Vibrations of Cantilever Beamshttps://emweb.unl.edu/mechanics-pages/scott-whitney/325hweb/beams.htm