Beam CalculatorLoads, sections & elastic response

Beam calculators / Loads & geometry

Trace the load. Understand the beam.

Ridge Beam Height Geometry Calculator

Calculate ideal roof rise and slope geometry above a stated support level.

Your model, explained visually

Model geometry

Your beam & loading inputs

m
in/12 in

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

h=rrunp12
θ=arctan(p12)

r run is horizontal run; p is rise per 12 units of run. θ is roof slope angle.

Calculate ideal roof rise and slope geometry above a stated support level.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
This is roof geometry, not ridge member sizing, bearing, connection design or a roof-load calculation.

Ridge Beam Height Geometry: model and interpretation

Calculate ideal roof rise and slope geometry above a stated support level. This is roof geometry, not ridge member sizing, bearing, connection design or a roof-load calculation.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Ridge Beam Height Geometry Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Horizontal half-run = 4 m; Rise per 12 horizontal units = 6 in/12 in.

OutputComputed result
Geometric roof rise2 m
Slope angle26.565051 degrees
Ideal slope length4.472136 m

How the stated input changes the result

ScenarioChanged input / basisResult
2 mHorizontal half-run1 m
3 mHorizontal half-run1.5 m
4 mHorizontal half-run2 m
5 mHorizontal half-run2.5 m
6 mHorizontal half-run3 m
8 mHorizontal half-run4 m

Unchanged inputs use: Dimension units = Metric dimensions; Horizontal half-run = 4 m; Rise per 12 horizontal units = 6 in/12 in. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

This is roof geometry, not ridge member sizing, bearing, connection design or a roof-load calculation.

How do I use this ridge beam height geometry calculator?

Calculate ideal roof rise and slope geometry above a stated support level.
h=rrunp12
θ=arctan(p12)

r run is horizontal run; p is rise per 12 units of run. θ is roof slope angle.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Prealgebra, volume and surface-area geometryhttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors