Beam CalculatorLoads, sections & elastic response

Beam calculators / Model-only limits

Trace the load. Understand the beam.

Required Beam Moment of Inertia Calculator

Calculate the continuous second moment of area needed to meet a supplied elastic deflection ratio.

Your model, explained visually

Model geometry

Your beam & loading inputs

m
GPa
kN/m

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Irequired=5wL3n384E

Deflection-only second moment for a simply supported beam under uniform load; n is the entered span-to-deflection ratio.

Calculate the continuous second moment of area needed to meet a supplied elastic deflection ratio.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Deflection-only inverse for the stated ideal beam. It does not select a beam size or check strength and stability.

Required Beam Moment of Inertia: model and interpretation

Calculate the continuous second moment of area needed to meet a supplied elastic deflection ratio. Deflection-only inverse for the stated ideal beam. It does not select a beam size or check strength and stability.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Required Beam Moment of Inertia Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Beam length / first span = 6 m; Elastic modulus = 200 GPa; Uniform line load = 5 kN/m; Chosen deflection denominator L/n = 360 .

OutputComputed result
Deflection-only required second moment2,531.25 cm⁴

How the stated input changes the result

ScenarioChanged input / basisResult
3 mBeam length / first span316.40625 cm⁴
4.5 mBeam length / first span1,067.871094 cm⁴
6 mBeam length / first span2,531.25 cm⁴
7.5 mBeam length / first span4,943.847656 cm⁴
9 mBeam length / first span8,542.96875 cm⁴
12 mBeam length / first span20,250 cm⁴

Unchanged inputs use: Dimension units = Metric dimensions; Beam length / first span = 6 m; Elastic modulus = 200 GPa; Uniform line load = 5 kN/m; Chosen deflection denominator L/n = 360 . Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Deflection-only inverse for the stated ideal beam. It does not select a beam size or check strength and stability.

How do I use this required beam moment of inertia calculator?

Calculate the continuous second moment of area needed to meet a supplied elastic deflection ratio.
Irequired=5wL3n384E

Deflection-only second moment for a simply supported beam under uniform load; n is the entered span-to-deflection ratio.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • American Wood Council Design Aid 6: Beam Design Formulas, simple uniform and central point-load caseshttps://awc.org/wp-content/uploads/2021/12/AWC-DA6-BeamFormulas-0710.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors