Beam CalculatorLoads, sections & elastic response

Beam calculators / Stress & stiffness

Trace the load. Understand the beam.

Flitch Beam Elastic Stiffness Calculator

Calculate no-slip flexural rigidity of full-depth side-by-side plies with a common neutral axis.

Your section, explained visually

Section geometry

Your beam & loading inputs

mm
mm
mm
GPa
GPa

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

EI=EwIw+EsIs
Iw=bwh312
Is=bsh312

Subscripts w and s denote wood and steel. bw is combined wood width, bs is steel width, and h is shared depth. Perfect bond and a common bending axis are assumed.

Calculate no-slip flexural rigidity of full-depth side-by-side plies with a common neutral axis.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Perfect composite action is assumed, not proven. No bolt spacing, interface slip, load transfer, stability, bearing or allowable resistance.

Flitch Beam Elastic Stiffness: model and interpretation

Calculate no-slip flexural rigidity of full-depth side-by-side plies with a common neutral axis. Perfect composite action is assumed, not proven. No bolt spacing, interface slip, load transfer, stability, bearing or allowable resistance.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Flitch Beam Elastic Stiffness Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Common ply depth = 300 mm; Combined wood ply width = 100 mm; Centred steel plate thickness = 10 mm; Supplied effective wood E = 10 GPa; Supplied steel E = 200 GPa.

OutputComputed result
Perfect-bond common-axis flexural rigidity6,750 kN·m²
Wood contribution2,250 kN·m²
Steel contribution4,500 kN·m²

How the stated input changes the result

ScenarioChanged input / basisResult
150 mmCommon ply depth843.75 kN·m²
225 mmCommon ply depth2,847.65625 kN·m²
300 mmCommon ply depth6,750 kN·m²
375 mmCommon ply depth13,183.59375 kN·m²
450 mmCommon ply depth22,781.25 kN·m²
600 mmCommon ply depth54,000 kN·m²

Unchanged inputs use: Dimension units = Metric dimensions; Common ply depth = 300 mm; Combined wood ply width = 100 mm; Centred steel plate thickness = 10 mm; Supplied effective wood E = 10 GPa; Supplied steel E = 200 GPa. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Perfect composite action is assumed, not proven. No bolt spacing, interface slip, load transfer, stability, bearing or allowable resistance.

How do I use this flitch beam elastic stiffness calculator?

Calculate no-slip flexural rigidity of full-depth side-by-side plies with a common neutral axis.
EI=EwIw+EsIs
Iw=bwh312
Is=bsh312

Subscripts w and s denote wood and steel. bw is combined wood width, bs is steel width, and h is shared depth. Perfect bond and a common bending axis are assumed.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Missouri University of Science and Technology, Mechanics of Materials: Composite Beams and Transformed-Section Methodhttps://web.mst.edu/jthomas/classes/2210/concepts/08/composite/index.html
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors