Beam CalculatorLoads, sections & elastic response

Beam calculators / Optical & lighting beams

Trace the load. Understand the beam.

Lighting Beam Angle Footprint Calculator

Calculate the geometric circular footprint on a plane perpendicular to a conical beam.

Your light beam, explained visually

Optical model

Your beam & loading inputs

m
degrees

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

D=2ztan(θfull2)

D is footprint diameter on a perpendicular plane, z is distance, and θ full is the full beam angle.

Calculate the geometric circular footprint on a plane perpendicular to a conical beam.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
A photometric beam angle commonly references half-maximum intensity directions. Geometric footprint is not a uniform illuminance boundary or a lux guarantee; no radar or ultrasonic refraction model.

Lighting Beam Angle Footprint: model and interpretation

Calculate the geometric circular footprint on a plane perpendicular to a conical beam. A photometric beam angle commonly references half-maximum intensity directions. Geometric footprint is not a uniform illuminance boundary or a lux guarantee; no radar or ultrasonic refraction model.
For an ideal Gaussian laser beam, w is the radius at 1/e² irradiance and divergence is a half-angle unless explicitly doubled. A lighting beam angle is instead a full angular width tied to a stated photometric convention. Do not interchange radius with diameter or half-angle with full-angle.
The formula is evaluated under its stated ideal spatial model. Geometric spot size is not a uniform illuminance guarantee, measured hot-spot map, laser safety assessment or a model of a structural member.

Check the numbers

Lighting Beam Angle Footprint Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Perpendicular throw distance = 3 m; Full beam angle = 40 degrees.

OutputComputed result
Geometric perpendicular-plane footprint2.183821 m diameter
Circular footprint area3.745623 m²

How the stated input changes the result

ScenarioChanged input / basisResult
1.5 mPerpendicular throw distance1.091911 m diameter
2.25 mPerpendicular throw distance1.637866 m diameter
3 mPerpendicular throw distance2.183821 m diameter
3.75 mPerpendicular throw distance2.729777 m diameter
4.5 mPerpendicular throw distance3.275732 m diameter
6 mPerpendicular throw distance4.367643 m diameter

Unchanged inputs use: Dimension units = Metric dimensions; Perpendicular throw distance = 3 m; Full beam angle = 40 degrees. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

A photometric beam angle commonly references half-maximum intensity directions. Geometric footprint is not a uniform illuminance boundary or a lux guarantee; no radar or ultrasonic refraction model.

How do I use this lighting beam angle footprint calculator?

Calculate the geometric circular footprint on a plane perpendicular to a conical beam.
D=2ztan(θfull2)

D is footprint diameter on a perpendicular plane, z is distance, and θ full is the full beam angle.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this calculate a structural beam?

No. This page concerns the stated optical or lighting beam geometry. It does not analyze a load-bearing member or determine laser protective equipment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • CIE International Lighting Vocabulary, 17-27-077: beam anglehttps://cie.co.at/eilvterm/17-27-077
  • TORMIN manufacturer, Beam Coverage Calculator: full-angle cone geometry and limitshttps://tormin.com/resources/lighting-calculators/beam-coverage/
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors