Beam CalculatorLoads, sections & elastic response

Beam calculators / Stress & stiffness

Trace the load. Understand the beam.

Circular Beam Bending and Shear Stress Calculator

Calculate extreme-fibre elastic bending stress and neutral-axis beam shear stress.

Your section, explained visually

Section geometry

Your beam & loading inputs

mm
kN·m
kN

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

σ=−M(y−y¯)Ix
τneutral=VQIxbneutral

Normal stress is tension-positive. Q is the first area moment above the neutral axis; b at the neutral axis is the local material breadth.

Calculate extreme-fibre elastic bending stress and neutral-axis beam shear stress.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
Straight-beam elastic stress, ideal section, no stress concentrations, residual stress, buckling or allowable strength determination.

Circular Beam Bending and Shear Stress: model and interpretation

Calculate extreme-fibre elastic bending stress and neutral-axis beam shear stress. Straight-beam elastic stress, ideal section, no stress concentrations, residual stress, buckling or allowable strength determination.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Circular Beam Bending and Shear Stress Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Outside / solid diameter = 100 mm; Signed bending moment = 10 kN·m; Shear force magnitude = 10 kN.

OutputComputed result
Largest absolute extreme-fibre bending stress101.859164 MPa
Top normal stress (tension positive)-101.859164 MPa
Bottom normal stress (tension positive)101.859164 MPa
Neutral-axis transverse shear magnitude1.697653 MPa
First moment above neutral axis83,333.333333 mm³

How the stated input changes the result

ScenarioChanged input / basisResult
5 kN·mSigned bending moment50.929582 MPa
7.5 kN·mSigned bending moment76.394373 MPa
10 kN·mSigned bending moment101.859164 MPa
12.5 kN·mSigned bending moment127.323954 MPa
15 kN·mSigned bending moment152.788745 MPa
20 kN·mSigned bending moment203.718327 MPa

Unchanged inputs use: Dimension units = Metric dimensions; Outside / solid diameter = 100 mm; Signed bending moment = 10 kN·m; Shear force magnitude = 10 kN. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

Straight-beam elastic stress, ideal section, no stress concentrations, residual stress, buckling or allowable strength determination.

How do I use this circular beam bending and shear stress calculator?

Calculate extreme-fibre elastic bending stress and neutral-axis beam shear stress.
σ=−M(y−y¯)Ix
τneutral=VQIxbneutral

Normal stress is tension-positive. Q is the first area moment above the neutral axis; b at the neutral axis is the local material breadth.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • American Wood Council Design Aid 6: Beam Design Formulas, simple uniform and central point-load caseshttps://awc.org/wp-content/uploads/2021/12/AWC-DA6-BeamFormulas-0710.pdf
  • Penn State Mechanics Map: area moments of inertia by composite parts and parallel-axis theoremhttps://mechanicsmap.psu.edu/websites/A2_moment_intergrals/A2-9_area_moments_composite/areamomentcomposite.html
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors
  • Jonkoping University Applied Mechanics: Beam Theory, first moment, transverse shear and section modulushttps://mechanics.ju.se/SolidMechanics/BeamTheory.html
  • University of Illinois: Introductory Solid Mechanics, beams in bending and transformed sectionshttps://mechref.engr.illinois.edu/sol/bending.html