Beam CalculatorLoads, sections & elastic response

Beam calculators / Loads & geometry

Trace the load. Understand the beam.

Wall Load on Beam Calculator

Calculate a uniform wall gravity load using a supplied equivalent material density.

Your model, explained visually

Model geometry

Your beam & loading inputs

mm
m
kg/m³

Starting values are editable examples. Confirm actual supports, loads, section and material properties. Dimension switching converts geometry only; loads and properties keep their printed units.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

wwall=ρgth

t is wall thickness and h is wall height. Convert dimensions to consistent units before applying the expression.

Calculate a uniform wall gravity load using a supplied equivalent material density.
  1. Confirm support constraints, loading plane, section and units.
  2. Enter actual geometry, loads and justified material properties.
  3. Submit the form, then interpret the result with the assumptions and limits below.
No openings, lintel action, arching, eccentricity, wall restraint or load spreading.

Wall Load on Beam: model and interpretation

Calculate a uniform wall gravity load using a supplied equivalent material density. No openings, lintel action, arching, eccentricity, wall restraint or load spreading.
The boundary conditions are part of the model. A pin, roller, fixed support and free end impose different translation and rotation constraints. Actual connection stiffness, continuity, bracing and load introduction can materially change a real beam response.
The worked example prints the complete input basis. Each comparison row changes the labelled quantity while retaining the other example inputs. A numerical elastic response should be distinguished from an allowable design value or a manufacturer span table.

Check the numbers

Wall Load on Beam Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric dimensions; Wall thickness = 150 mm; Supported wall height = 3 m; Wall material bulk density = 1800 kg/m³.

OutputComputed result
Uniform equivalent wall gravity load7.943386 kN/m

How the stated input changes the result

ScenarioChanged input / basisResult
1.5 mSupported wall height3.971693 kN/m
2.25 mSupported wall height5.95754 kN/m
3 mSupported wall height7.943386 kN/m
3.75 mSupported wall height9.929233 kN/m
4.5 mSupported wall height11.91508 kN/m
6 mSupported wall height15.886773 kN/m

Unchanged inputs use: Dimension units = Metric dimensions; Wall thickness = 150 mm; Supported wall height = 3 m; Wall material bulk density = 1800 kg/m³. Results retain the model limitations described above.

Common questions

What limitation matters for this calculation?

No openings, lintel action, arching, eccentricity, wall restraint or load spreading.

How do I use this wall load on beam calculator?

Calculate a uniform wall gravity load using a supplied equivalent material density.
wwall=ρgth

t is wall thickness and h is wall height. Convert dimensions to consistent units before applying the expression.

What do the starting values represent?

They are editable numerical examples. Measure actual dimensions and use material properties, support details and loads appropriate to the real member. They are not prescribed design values or a stock-size recommendation.

Does this result establish a safe beam size?

No. The stated calculation does not establish building-code compliance, allowable strength, connection capacity, stability, fire resistance or suitability for construction. A complete structural design needs all relevant checks and a qualified project-specific assessment.

Which unit system does the calculator use?

Dimension switching converts the labelled length inputs. Forces, line loads, elastic modulus and other properties retain the units printed beside them. Results include common metric and imperial equivalents where meaningful.

Can I export the calculation to Excel?

After calculation, Export CSV saves numerical results and submitted inputs. This is a text table, not a native Excel formula workbook, proprietary analysis file or signed engineering report.

Where do the formulas come from?

Published references appear below with full plain-text addresses. Formulas, assumptions, worked examples and comparison tables are stored directly in the pages; no external property lookup is required.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax University Physics, density is mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • US HUD, Residential Structural Design Guide 2000, Section 2.3.1: vertical loads and tributary areashttps://www.huduser.gov/portal/Publications/pdf/residential-old2000.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors